• December 08, 2019, 05:19:55 PM
Welcome, Guest. Please login or register. Registration is free.
Did you miss your activation email?

Author Topic: baystack 5520-48T-PWR no boot  (Read 1552 times)

0 Members and 1 Guest are viewing this topic.

Offline pued

  • Rookie
  • **
  • Posts: 19
baystack 5520-48T-PWR no boot
« on: August 16, 2019, 01:24:36 AM »
Can not boot to the normal page.
Can't reset the IP

Booting...

Testing Memory...............................

Starting..

Ethernet Routing Switch 5520-48T-PWR

Hardware Rev :    8

CPU CLOCK :266000000
Resets: 64.
Initializing Flash..
Reading MAC Address..
MAC Address: 00:16:60:A7:70:00
Initializing Switch CBs

  PoE Firmware Info  :
     Version number  : 8
     Product number  : 6370
     Build           : 4

PCI unit 0: Dev 0x5670, Rev 0x02, Chip BCM5670_A1, Driver BCM5670_A0
PCI unit 1: Dev 0x5695, Rev 0x11, Chip BCM5695_B0, Driver BCM5695_A0
PCI unit 2: Dev 0x5695, Rev 0x11, Chip BCM5695_B0, Driver BCM5695_A0
PCI unit 3: Dev 0x5695, Rev 0x11, Chip BCM5695_B0, Driver BCM5695_A0
PCI unit 4: Dev 0x5695, Rev 0x11, Chip BCM5695_B0, Driver BCM5695_A0
Attaching SOC unit 0... PCI device BCM5670_A1 attached as unit 0.
Attaching SOC unit 1... PCI device BCM5695_B0 attached as unit 1.
Attaching SOC unit 2... PCI device BCM5695_B0 attached as unit 2.
Attaching SOC unit 3... PCI device BCM5695_B0 attached as unit 3.
Attaching SOC unit 4... PCI device BCM5695_B0 attached as unit 4.

Diagnostic Version 6.0.0.6 Oct 29 2008, 12:10:55



Test 102  ROM  Config                - PASSED
Test 104  FANs                       - PASSED
Test 105  Ext Flash Id Get           - PASSED
Test 207  XGS SWITCH Registers       - PASSED
Test 208  FABRIC Registers           - PASSED
Test 211  PHYs Register              - PASSED
Test 212  Internal Loopback          - PASSED
 Press Esc to Enter Diag

## NO Agent Code Found
Boot fail chang to next agent try again


## NO Agent Code Found


Press 'a'  Launch Primary   Agent [ 2 ]  Vers: (unknown)
Press 'b'  Launch Secondary Agent [ 1 ]  Vers: (unknown)
Press 'c'  Toggle Primary   Agent Selection
Press 'd'  to Download agent code
Press 'e'  to display Errors
Press 'i'  to Initialize config/log config control in Both flash
Press 'p'  to run POST tests
Press 's'  to run Stack external loopback test


Offline krc

  • Rookie
  • **
  • Posts: 15
Re: baystack 5520-48T-PWR no boot
« Reply #1 on: August 28, 2019, 04:40:00 PM »
did you do:
Press 'i'  to Initialize config/log config control in Both flash

Offline rklopoto

  • Rookie
  • **
  • Posts: 3
Re: baystack 5520-48T-PWR no boot
« Reply #2 on: August 29, 2019, 09:26:20 AM »
If not, you might have a corrupted agent.  If you choose 'd', it will allow you to upload a new version of code.

Offline pued

  • Rookie
  • **
  • Posts: 19
Re: baystack 5520-48T-PWR no boot
« Reply #3 on: August 29, 2019, 10:22:24 PM »
did you do:
Press 'i'  to Initialize config/log config control in Both flash

I did it and it didn't work. still the same

Offline pued

  • Rookie
  • **
  • Posts: 19
Re: baystack 5520-48T-PWR no boot
« Reply #4 on: August 29, 2019, 10:23:36 PM »
If not, you might have a corrupted agent.  If you choose 'd', it will allow you to upload a new version of code.
I reload but can't access. The program runs as if loaded but still doesn't.